Skip to Content

Changes for page Radio Log

Last modified by Treyfane Dingo on 2025/04/27 13:33
From version 23.4
edited by Treyfane Dingo
on 2025/04/07 21:51
Change comment: There is no comment for this version
To version 23.2
edited by Treyfane Dingo
on 2025/04/07 21:48
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -3,11 +3,11 @@
3 3  
4 4  The Radio Log is a module, which can be called by pressing F8 anywhere in L.A.S.S.I.E.. It will be available if L.A.S.S.I.E. is connected to a [[Pi-Star>>https://www.pistar.uk/]] with [[pistarlog2ws>>https://git.furcom.org/Dingo/pistarlog2ws]] installed (green antenna symbol) and subsequently show the DMR radio traffic.
5 5  
6 -= Pi-Star Preparation =
6 += Pi-Star =
7 7  
8 8  == OS Installation ==
9 9  
10 -Pi-Star has to be installed on a Raspberry Pi (Zero) with a MMDVM HAT. A non-duplex MMDVM HAT is fully sufficient since Pi-Star only can monitor one single frequency and sending is not something this setup is expected to do. See [[https:~~/~~/www.pistar.uk/downloads/>>https://www.pistar.uk/downloads/]] for image download and installation instructions.
10 +Pi-Star has to be installed on a Raspberry Pi (Zero) with a MMDVM HAT. A non-duplex MMDVM HAT is fully sufficient since Pi-Star only can monitor one single frequency and sending is not something this setup is expected to do. See [[https:~~/~~/www.pistar.uk/downloads/>>https://www.pistar.uk/downloads/]] for download and installation instructions.
11 11  
12 12  The SD card for the Raspberry Pi will be flashed using [[Raspberry Pi Imager>>https://www.raspberrypi.com/software/]]. During the process, you will be asked if you like to apply OS customization settings. You can change the //hostname//, //wireless LAN// and //locale settings// here. **Do not set username and password, or anything in the Services or Options tab!**
13 13  
... ... @@ -48,29 +48,6 @@
48 48  
49 49  [[image:radiolog_cfg6.png]]
50 50  
51 -= Installing pistarlog2ws =
51 +Installing the L.A.S.S.I.E. websocket connection
52 52  
53 -The pistarlog2ws repository can be found at the [[FURCOM GIT>>https://git.furcom.org/Dingo/pistarlog2ws]]. To install it, you have to connect to the Pi-Star via ssh.
54 -
55 -//Pi-Star's disk is read-only by default, so you have to enable read-write with rpi-rw.//
56 -
57 -Clone the repository into the pi-star home and run the install script:
58 -
59 -{{{rpi-rw
60 -git clone https://git.furcom.org/dingo/pistarlog2ws
61 -cd pistarlog2ws
62 -./install.sh
63 -}}}
64 -
65 -This should install and enable the websocket service and make the necessary adjustments to the firewall.
66 -
67 -== ==
68 -
69 -== Test ==
70 -
71 -You can test the installation from another machine in the network using nc or wscat.
72 -
73 -{{{nc -zv <IP-ADDRESS OF PI-STAR> 8765
74 -}}}
75 -
76 -{{{wscat -c ws://<IP-ADDRESS OF PI-STAR>:8765 --no-color}}}
53 +