Skip to Content

Changes for page Radio Log

Last modified by Treyfane Dingo on 2025/04/27 13:33
From version 22.2
edited by Treyfane Dingo
on 2025/04/07 21:42
Change comment: There is no comment for this version
To version 25.3
edited by Treyfane Dingo
on 2025/04/07 22:12
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,13 +1,13 @@
1 1  (% data-widget="image" contenteditable="false" tabindex="-1" %)[[image:radiolog1.png]](% title="Click and drag to resize" %)​
2 2  
3 3  
4 -The Radio Log is a module, which can be called by pressing F8 anywhere in L.A.S.S.I.E.. It will be available if L.A.S.S.I.E. is connected to a [[Pi-Star>>https://www.pistar.uk/]] with [[pistarlog2ws>>https://git.furcom.org/Dingo/pistarlog2ws]] installed (green antenna symbol) and subsequently show the DMR radio traffic.
4 +The **Radio Log** is a module, which can be called by pressing F8 anywhere in L.A.S.S.I.E.. It will be available if L.A.S.S.I.E. is connected to a [[Pi-Star>>https://www.pistar.uk/]] with [[pistarlog2ws>>https://git.furcom.org/Dingo/pistarlog2ws]] installed (green antenna symbol) and subsequently show the DMR radio traffic.
5 5  
6 -= Pi-Star =
6 += Pi-Star Preparation =
7 7  
8 8  == OS Installation ==
9 9  
10 -Pi-Star has to be installed on a Raspberry Pi (Zero) with a MMDVM HAT. A non-duplex MMDVM HAT is fully sufficient since Pi-Star only can monitor one single frequency and sending is not something this setup is expected to do. See [[https:~~/~~/www.pistar.uk/downloads/>>https://www.pistar.uk/downloads/]] for download and installation instructions.
10 +Pi-Star has to be installed on a Raspberry Pi (Zero) with a MMDVM HAT. A non-duplex MMDVM HAT is fully sufficient since Pi-Star only can monitor one single frequency and sending is not something this setup is expected to do. See [[https:~~/~~/www.pistar.uk/downloads/>>https://www.pistar.uk/downloads/]] for image download and installation instructions.
11 11  
12 12  The SD card for the Raspberry Pi will be flashed using [[Raspberry Pi Imager>>https://www.raspberrypi.com/software/]]. During the process, you will be asked if you like to apply OS customization settings. You can change the //hostname//, //wireless LAN// and //locale settings// here. **Do not set username and password, or anything in the Services or Options tab!**
13 13  
... ... @@ -36,7 +36,7 @@
36 36  
37 37  [[image:radiolog_cfg2c.png]]
38 38  
39 -In the “Wireless Configuration”, the IP address of the Pi-Star acquired by DHCP is shown. This IP address has to be configured as “IP for a FurCom Services Radio Log system” in L.A.S.S.I.E. (System Settings → General Settings).
39 +Back on the regular configuration page, in the “Wireless Configuration”, the IP address of the Pi-Star acquired by DHCP is shown. This IP address has to be configured as “IP for a FurCom Services Radio Log system” in L.A.S.S.I.E. (System Settings → General Settings).
40 40  
41 41  [[image:radiolog_cfg4.png]]
42 42  
... ... @@ -44,5 +44,39 @@
44 44  
45 45  [[image:radiolog_cfg5.png]]
46 46  
47 +You also should run an Update of the Pi-Star using the “Configuration” → “Update” page.
47 47  
48 -
49 +After all of the configuration, the “Dashboard” of the Pi-Star should look like this (frequency may vary):
50 +
51 +[[image:radiolog_cfg6.png]]
52 +
53 += Installing pistarlog2ws =
54 +
55 +The pistarlog2ws repository can be found at the [[FURCOM GIT>>https://git.furcom.org/Dingo/pistarlog2ws]]. To install it, you have to connect to the Pi-Star via ssh.
56 +
57 +//Pi-Star's disk is read-only by default, so you have to enable read-write with “rpi-rw”.//
58 +
59 +Clone the repository into the pi-star home and run the install script:
60 +
61 +{{{rpi-rw
62 +git clone https://git.furcom.org/dingo/pistarlog2ws
63 +cd pistarlog2ws
64 +./install.sh
65 +}}}
66 +
67 +This should install and enable the websocket service and make the necessary adjustments to the firewall.
68 +
69 +== Test ==
70 +
71 +You can test the installation from another machine in the network using “nc” or “wscat”.
72 +
73 +{{{nc -zv <IP-ADDRESS OF PI-STAR> 8765
74 +}}}
75 +
76 +{{{wscat -c ws://<IP-ADDRESS OF PI-STAR>:8765 --no-color}}}
77 +
78 += DMR ID Naming =
79 +
80 +To have the readable nickname in the Radio Log rather than the DMR ID, the respective Radio has to be handed out to the Operative via the Personal Assets Database. The DMR ID has to be set as Information
81 +
82 +[[image:radiolog_asset.png]]
radiolog_asset.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.dingo
Size
... ... @@ -1,0 +1,1 @@
1 +24.0 KB
Content
radiolog_cfg6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.dingo
Size
... ... @@ -1,0 +1,1 @@
1 +111.3 KB
Content