Skip to Content

Changes for page Radio Log

Last modified by Treyfane Dingo on 2025/04/27 13:33
From version 18.5
edited by Treyfane Dingo
on 2025/04/07 21:25
Change comment: There is no comment for this version
To version 11.2
edited by Treyfane Dingo
on 2025/04/07 21:00
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,4 +1,4 @@
1 -(% data-widget="image" contenteditable="false" tabindex="-1" %)[[image:radiolog1.png]](% title="Click and drag to resize" %)​
1 +[[image:radiolog1.png]]
2 2  
3 3  
4 4  The Radio Log is a module, which can be called by pressing F8 anywhere in L.A.S.S.I.E.. It will be available if L.A.S.S.I.E. is connected to a [[Pi-Star>>https://www.pistar.uk/]] with [[pistarlog2ws>>https://git.furcom.org/Dingo/pistarlog2ws]] installed (green antenna symbol) and subsequently show the DMR radio traffic.
... ... @@ -9,36 +9,14 @@
9 9  
10 10  Pi-Star has to be installed on a Raspberry Pi (Zero) with a MMDVM HAT. A non-duplex MMDVM HAT is fully sufficient since Pi-Star only can monitor one single frequency and sending is not something this setup is expected to do. See [[https:~~/~~/www.pistar.uk/downloads/>>https://www.pistar.uk/downloads/]] for download and installation instructions.
11 11  
12 -The SD card for the Raspberry Pi will be flashed using [[Raspberry Pi Imager>>https://www.raspberrypi.com/software/]]. During the process, you will be asked if you like to apply OS customization settings. You can change the //hostname//, //wireless LAN// and //locale settings// here. **Do not set username and password, or anything in the Services or Options tab!**
12 +The image downloaded will be flashed to a SD card using the [[Raspberry Pi Imager>>https://www.raspberrypi.com/software/]]. While flashing, when asked if you like to apply OS customization settings, you can set the hostname, the wireless LAN and locale settings. **Do not set / change Usernany settings in Services or Options!**
13 13  
14 -**~ **[[image:radiolog_set3.png]]
14 +[[image:radiolog_set3.png]]
15 15  
16 -After flashing and booting the Raspberry from the SD card, you should be able to access the Pi-Star webinterface via browser at e.g. [[http:~~/~~/radiolog.local/admin/>>http://radiolog.local/admin/]]
16 +After flashing the SD card and booting the Raspberry with it, your Pi-Star should be accessible via webinterface, e.g. [[https:~~/~~/radiolog.local/admin/>>https://radiolog.local/admin/]]
17 17  
18 -Default Username: pi-star
19 -Default Password: raspberry
20 -
21 21  == Configuration ==
22 22  
23 -After installing Pi-Star, the following configuration should be used for the Radio Log. First, in the “MMDVMHost Configuration” section the DMR Mode should be enabled. Please remember to press “Apply Changes” after changing every section.
20 +After Pi-Star is installed, the following configuration should be done.
24 24  
25 -[[image:radiolog_cfg1.png]]
26 -
27 -In the “General Configuration” section the Radio Frequency has to be set to the **output** frequency of your DMR repeater. Also the correct Radio/Modem Type has to be selected, depending on the MMDVM HAT used, and the Node Type has to be set to “Public”.
28 -
29 -[[image:radiolog_cfg2.png]]
30 -
31 -In the “DMR Configuration” section it is imperative to disable all three Networks. We don't want to have the Radio Log Pi-Star send out our private DMR communication to the world after all.
32 -
33 -[[image:radiolog_cfg3.png]]
34 -
35 -In the “Wireless Configuration”, the IP address of the Pi-Star acquired by DHCP is shown. This IP address has to be configured as “IP for a FurCom Services Radio Log system” in L.A.S.S.I.E. (System Settings → General Settings).
36 -
37 -[[image:radiolog_cfg4.png]]
38 -
39 -For the configuration to be completed and usable, you should change the default password to something more secure. Please remember
40 -
41 -[[image:radiolog_cfg5.png]]
42 -
43 -
44 -
22 +(% contenteditable="false" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhDgAOAIAAAAAAAP///yH5BAAAAAAALAAAAAAOAA4AAAIMhI+py+0Po5y02qsKADs=||data-widget="uploadimage"]](% style="background:rgba(220, 220, 220, 0.5) url(~"https://wiki.furcom.org/webjars/wiki%3Axwiki/xwiki-platform-ckeditor-webjar/16.10.5/plugins/widget/images/handle.png~"); left:0px; top:-15px" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]][[image:data:image/gif;base64,R0lGODlhDgAOAIAAAAAAAP///yH5BAAAAAAALAAAAAAOAA4AAAIMhI+py+0Po5y02qsKADs=||data-widget="uploadimage"]][[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]][[image:radiolog_cfg3.png]][[image:radiolog_cfg4.png]][[image:radiolog_cfg5.png]]