Skip to Content

Changes for page Radio Log

Last modified by Treyfane Dingo on 2025/04/27 13:33
From version 15.3
edited by Treyfane Dingo
on 2025/04/07 21:11
Change comment: There is no comment for this version
To version 10.5
edited by Treyfane Dingo
on 2025/04/07 20:47
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,28 +1,15 @@
1 -(% data-widget="image" contenteditable="false" tabindex="-1" %)[[image:radiolog1.png]](% title="Click and drag to resize" %)​
1 +[[image:radiolog1.png]]
2 2  
3 3  
4 4  The Radio Log is a module, which can be called by pressing F8 anywhere in L.A.S.S.I.E.. It will be available if L.A.S.S.I.E. is connected to a [[Pi-Star>>https://www.pistar.uk/]] with [[pistarlog2ws>>https://git.furcom.org/Dingo/pistarlog2ws]] installed (green antenna symbol) and subsequently show the DMR radio traffic.
5 5  
6 -= Pi-Star =
6 += Pi-Star Installation =
7 7  
8 -== Installation ==
8 +Pi-Star has to be installed on a Raspberry Pi (Zero) with a MMDVM HAT. A non-duplex MMDVM HAT is fully sufficient since Pi-Star only can monitor one single frequency and sending is not something this setup is expected to do. See [[https:~~/~~/www.pistar.uk/downloads/>>https://www.pistar.uk/downloads/]] for download and instructions. The image will be flashed to a SD C
9 9  
10 -Pi-Star has to be installed on a Raspberry Pi (Zero) with a MMDVM HAT. A non-duplex MMDVM HAT is fully sufficient since Pi-Star only can monitor one single frequency and sending is not something this setup is expected to do. See [[https:~~/~~/www.pistar.uk/downloads/>>https://www.pistar.uk/downloads/]] for download and installation instructions.
10 +After Pi-Star is installed , the following configuration should be done. To configure the freshly installed Pi-Star, connect to the web interface using your hostname, e.g. [[http:~~/~~/radiolog.local/admin/>>http://radiolog.local/admin/]]
11 11  
12 -The SD card for the Raspberry Pi will be flashed using [[Raspberry Pi Imager>>https://www.raspberrypi.com/software/]]. During the process, you will be asked if you like to apply OS customization settings. You can change the //hostname//, //wireless LAN// and //locale settings// here. **Do not set username and password, or anything in the Services or Options tab!**
12 +Pi-Star Configuration
13 13  
14 -**~ **[[image:radiolog_set3.png]]
15 15  
16 -After flashing and booting the Raspberry from the SD card, you should be able to access the Pi-Star Webinterface via browser at e.g. [[http:~~/~~/radiolog.local/admin/>>http://radiolog.local/admin/]]
17 -
18 -== Configuration ==
19 -
20 -After installing Pi-Star, the following configuration should be used for the Radio Log. First, in the MMDVMHost Configuration section the DMR Mode should be enabled. Please remember to press “Apply Changes” after changing every section.
21 -
22 -[[image:radiolog_cfg1.png]]
23 -
24 -In the General Configuration section the Radio Frequency has to be set to the **output** frequency of your repeater
25 -
26 -[[image:radiolog_cfg2.png]]
27 -
28 -
15 +[[image:radiolog_cfg1.png]][[image:radiolog_cfg2.png]][[image:radiolog_cfg3.png]][[image:radiolog_cfg4.png]][[image:radiolog_cfg5.png]]
radiolog_set3.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.dingo
Size
... ... @@ -1,1 +1,0 @@
1 -48.9 KB
Content